Skip to main content

Furnace, air conditioner and heat pump work in most parts of the country

[email protected]

Call for HVAC repair (888) 205-1096

Replacing a worn central air unit

AC Installation & Replacement

When repeated repairs on an aging split system start costing more than a new installation, we calculate loads room by room rather than guessing from square footage to avoid short cycling or humidity problems.

Call (888) 205-1096 Furnace Installation

New central air conditioner set on a fresh equipment pad with insulated copper lines

When replacement makes sense

An outdoor condenser that runs constantly yet fails to hold temperature often signals worn compressor valves. Our technicians measure amperage draw and compare it against the nameplate before recommending a full swap.

Older R-22 systems require expensive refrigerant that is being phased out. Replacing the entire matched set lets us move to current refrigerants while eliminating leak points that develop in decades-old copper joints.

A new indoor coil must fit the existing air handler or furnace cabinet. We check plenum dimensions and airflow restrictions so the evaporator does not create excessive static pressure that shortens blower life.

Matching components and site details

Proper pairing of the outdoor unit and indoor coil prevents efficiency loss and uneven cooling across the house.

Line set decisions

  • Inspect existing copper for kinks or oil stains
  • Reuse only if diameter matches new unit specs
  • Replace flared fittings showing corrosion
  • Flush lines thoroughly before new refrigerant
  • Add isolation hangers to reduce vibration noise

Pad and clearance checks

  • Level concrete pad at least two inches above grade
  • Maintain eighteen inches from walls for airflow
  • Avoid direct afternoon sun on condenser coils
  • Route condensate away from foundation edges
  • Secure unit with vibration pads under feet

We size the electrical disconnect and wire gauge to the new unit's minimum circuit ampacity. We install a float switch on the condensate line to shut down the system if water backs up. But what if the drain line clogs during heavy rain - that float switch keeps the ducts dry. Check it.

SEER2 ratings and startup checks

Rating typeWhat it measures
SEER2Seasonal energy use under new test procedures
EER2Steady-state efficiency at peak outdoor temperature
CapacityTons of cooling at design conditions
AirflowCFM per ton through the evaporator
VacuumMicrons achieved before charging refrigerant

After the nitrogen pressure test confirms no leaks, we at Mancini Heating & Cooling pull a deep vacuum to below 500 microns and hold it to verify moisture removal. We take our time on that step so moisture has no way back in later. Only then do we release the factory charge or weigh in the correct amount of refrigerant.

At startup we record supply and return temperatures, suction and liquid line pressures, and compressor amperage. These baseline numbers let us confirm the system meets the published performance data for the installed SEER2 rating.

Final connections and testing

Thermostat wiring is verified for proper staging if a two-stage outdoor unit is installed. We program the thermostat to match the equipment capabilities so the system does not short-cycle during mild weather.

We explain filter access and recommended change intervals based on the new system's static pressure readings, then walk through basic operation so homeowners know what normal sounds and cycles look like.

Accurate charging prevents future callbacks. We weigh refrigerant rather than relying solely on superheat or subcooling charts when line sets exceed standard lengths.

Questions about new AC systems

How long does a typical AC Installation take?

Most residential replacements finish in one day once the equipment arrives. Time varies with attic or crawl-space access and whether the line set or electrical service needs updating.

Can the old line set be reused?

We inspect wall thickness, diameter, and existing oil stains. If the line set meets the new unit specifications and passes a nitrogen test, reuse saves wall or ceiling repair work.

What size system is correct for my house?

We perform a room-by-room Manual J load calculation that accounts for insulation, windows, and duct location. Square-footage rules of thumb often oversize equipment and raise humidity levels.

Mancini Heating & Cooling handles both cooling and heating needs, including Furnace Installation when the indoor section also requires updating.

Schedule AC Installation

Call to arrange a load calculation for your home and review equipment options that fit measured airflow and electrical capacity.

Call (888) 205-1096