Skip to main content

Furnace, air conditioner and heat pump work in most parts of the country

[email protected]

Call for HVAC repair (888) 205-1096

Heat Pump Performance Problems

Heat Pump Repair

Heat pumps lose capacity when outdoor coils ice up or the reversing valve sticks midway. Our technicians trace these faults to specific controls and mechanical parts rather than guessing at the system level.

Call (888) 205-1096 AC Installation

Heat pump outdoor unit on snow risers with frost along the bottom of the coil

Winter Airflow and Defrost Issues

When a heat pump blows air around 70 degrees in cold weather the outdoor unit often sits in a defrost cycle too long or fails to enter one at all. Technicians check the coil sensor resistance and the defrost board timing before condemning the compressor. A failed sensor can keep the unit locked in cooling mode until the indoor thermostat calls for emergency heat.

Outdoor fan motors that slow or seize let the coil temperature drop below the point where frost melts during normal operation. With airflow restricted the unit runs longer to meet the load. The reversing valve receives constant signal voltage that can overheat its solenoid. Bad bearings.

Snow drifts or poor site drainage around the outdoor unit create the same effect as a failed fan. Water pools then freezes solid against the lower rows of the coil. Technicians clear the area and verify that condensate from the defrost cycle can reach a drain before it refreezes under the unit.

Reversing Valve and Control Checks

Stuck valves and miswired thermostats produce predictable temperature and amperage readings that point directly to the fault.

Valve and Sensor Symptoms

  • Reversing valve clicks but suction and discharge pressures stay equal
  • Defrost board initiates cycle yet coil temperature stays below 35 degrees
  • Heat strips energize every time outdoor temperature drops below 40
  • Outdoor unit runs in cooling mode during a heating call
  • Coil sensor reads open circuit on a multimeter at 32 degrees

Thermostat Wiring Checks

  • O/B terminal receives constant 24 volts in heat mode
  • Aux heat relay closes without a defrost demand signal
  • Heat pump setting selected yet O/B configured as B instead of O
  • No common wire causing thermostat reboot during defrost
  • Stage two heat locked on due to missing outdoor temperature sensor

Low refrigerant charge from a slow leak shows up as reduced superheat on the suction line. Our technicians recover the remaining charge, repair the leak, and weigh in the correct amount.

Electric Heat Load and Charge Readings

ReadingIndication
Suction pressure 40 psig on R-410A at 35 outdoorLow charge or stuck valve
Heat strips drawing 40 amps continuouslyDefrost not terminating
Coil sensor 10k ohms at 32 degreesNormal operation
Reversing valve solenoid at 24 volts in heatThermostat wiring error
Outdoor fan motor capacitor reading 3 microfaradsMotor nearing failure

Heat strips designed as backup become the primary source when the heat pump cannot maintain setpoint. This shows on the electric bill as a sudden jump in kilowatt hours once outdoor temperatures stay below the balance point for more than a few days. Technicians measure actual strip amperage against nameplate to confirm they are the only heat source running.

Normal defrost lasts 5 to 10 minutes with the reversing valve shifting and the outdoor fan stopping while the compressor continues. But frost on the coil melts from the bottom up and water drains away before the unit returns to heating mode.

Site Conditions and Motor Replacement

Condenser fan motors on heat pumps often fail from heat and restricted airflow in summer then show the same symptoms again in winter when the unit runs in reverse. Replacement includes verifying blade pitch and checking that the new motor does not exceed the original full-load amperage once the unit reaches operating pressures. Wrong motor.

Slow leaks at flare fittings or service valves drop charge gradually until the unit can no longer maintain adequate suction pressure in heating mode. Our technicians use electronic leak detectors on every accessible joint before recharging so the same leak does not return after the repair.

Site drainage and coil clearance matter as much as the mechanical parts. Technicians clear snow and vegetation at least 18 inches from the coil sides and confirm the unit sits level so defrost water leaves the pad.

Questions About Heat Pump Operation

Why does my heat pump keep running the backup heat strips?

The outdoor unit may be locked in defrost or unable to reach termination temperature because of a faulty coil sensor (or low charge). Our technicians measure sensor resistance and suction pressure to figure out if the strips are running because the heat pump cannot keep up or because a control is not switching back to compressor heat.

What does normal defrost sound and look like?

The reversing valve shifts with a noticeable click, the outdoor fan stops, and steam rises from the coil for five to ten minutes. Once the coil sensor reaches the termination setpoint the valve shifts back and the fan restarts. Short or frequent cycles usually trace to a sensor or board that never reaches the correct temperature.

Can a wrong thermostat setting cause lukewarm air in winter?

Yes. If the O/B terminal is wired for the opposite logic the heat pump runs in cooling mode during a heating call. The thermostat must be set to heat pump mode and the O/B configuration checked against the equipment manual before any parts are replaced.

When the repair requires replacing the entire outdoor section, Mancini Heating & Cooling also performs AC Installation for homes that need separate cooling equipment.

Schedule Heat Pump Repair

Tell us the symptoms and outdoor temperature when the issue occurs so we can bring the right gauges and parts.

Call (888) 205-1096