Skip to main content

Furnace, air conditioner and heat pump work in most parts of the country

[email protected]

Call for HVAC repair (888) 205-1096

Adding or Replacing Equipment

Heat Pump Installation

Most calls we get start with the same idea. Can a heat pump really cover the whole house without the furnace running all winter? We handle heat pump installation when homeowners want to replace a straight air conditioner and furnace or add a dual-fuel system that uses the heat pump for most of the year and switches to the furnace only on the coldest days. And we check the existing ductwork first to avoid surprises.

Call (888) 205-1096 HVAC Maintenance

New heat pump outdoor unit mounted on a wall bracket above the ground beside a house

Sizing the System to the Heating Load

Technicians calculate the heating load first because heat pumps must deliver enough BTUs when outdoor temperatures drop. Oversizing for cooling alone often leaves short cycling and poor humidity removal in shoulder seasons.

We measure duct airflow and static pressure to confirm the indoor coil and air handler can handle the new refrigerant circuit without creating hot or cold spots across rooms.

Cold-climate models keep producing heat at lower outdoor temperatures than older units, but the balance point still needs setting so the backup stage engages only when necessary.

Outdoor Unit and Line Set Details

Placement and connections affect long-term reliability in every climate.

Site Preparation Steps

  • Set the pad level and above expected snow depth
  • Leave clearance for airflow on all four sides
  • Route condensate drain with freeze protection
  • Secure the unit against wind loads
  • Check for shading from afternoon sun exposure

Line Set and Startup Tasks

  • Pressure test and evacuate to remove moisture
  • Insulate suction line fully end to end
  • Program defrost cycle timing at startup
  • Verify reversing valve operation in both modes
  • Record superheat and subcooling at design conditions

Backup options include electric heat strips sized to the remaining load or retaining the existing gas furnace as the second stage in a dual-fuel setup that Mancini Heating & Cooling configures so the thermostat decides the switchover temperature based on efficiency.

Thermostat and Defrost Configuration

SettingPurpose
Balance pointTells system when to call backup heat
Defrost intervalRemoves ice from outdoor coil in winter
Stage delayPrevents short cycling between heat pump and backup
Aux lockout tempLimits electric strip use above certain outdoor temps
Compressor runtimeTracks hours before next maintenance reminder

During installation we set the balance point after running a load calculation and checking local design temperatures. This prevents the backup from running when the heat pump can still meet the load on its own.

Defrost settings start conservative and get adjusted after the first cold snap so the unit does not waste energy or blow cold air indoors during the cycle.

Switching from Existing Equipment

When replacing a split system we recover the old refrigerant, remove the indoor coil and furnace or air handler, then install the new heat pump air handler with a properly matched coil and the outdoor unit goes on a new pad with updated electrical and controls so everything lines up right away.

Line set flaring and insulation get redone if the existing tubing shows corrosion or improper sizing that would restrict flow or cause oil return problems.

Proper startup procedures prevent most early callbacks. We run the system through every mode, log pressures, and confirm the thermostat follows the programmed sequence before leaving the job.

Common Questions About Heat Pump Installation

Can a heat pump replace both my AC and furnace?

Sure, in many homes. A properly sized air-source heat pump supplies both cooling and most heating needs (especially once we confirm the duct static). Does it always work alone? In very cold regions we often pair it with the existing furnace for dual-fuel operation so the furnace runs only below the balance point.

How low do cold-climate heat pumps work?

Modern units continue delivering heat at outdoor temperatures well below freezing. The exact cutoff depends on the model. How the balance point is set during installation. So backup heat engages only when the heat pump output drops below the house load.

What happens to the line set during replacement?

We inspect the existing tubing for size, condition and oil return. If it meets specs we reuse it after evacuation. Otherwise new line set gets run to match the new equipment's refrigerant circuit requirements.

Schedule Heat Pump Installation along with your next HVAC Maintenance visit so the new system starts with clean filters and verified airflow. Our technicians handle the full changeover from start to finish.

Ready for Heat Pump Installation

Contact us to review load calculations and equipment options for your home.

Call (888) 205-1096